Vicon XX214-60-06 Installationsanleitung

www.vicon-security.com XX214-60-06Surveyor® HD Network Pressurized Camera DomesVicon Industries Inc. doe

Installation | 2-3 Accessory Kits The accessory kit includes hardware necessary to assist in assembling the Surveyor HD/SD; the screws and washers ar

2-4 | Chapter 2 Installation Note By default, when the pressure in the housing dips below 1/2 psig an On Screen Display message appears stating “Low

Installation | 2-5 MAC Address Surveyor HD Pressurized Network Dome XX214-60

2-6 | Chapter 2 Installation Quick Installation XX214-60

Detailed Installation | 2-7 Detailed Installation Installation is a simple process. Choose the installation type based on the mounting configuration.

2-8 | Chapter 2 Installation 3. Place a bead of silicone sealant around the wall mount mounting flange, press it to the surface and line up the fla

Detailed Installation | 2-9 Installing the 23-Pin Connector Assembly (If the prefabricated 23-pin cable assembly is used.) 6. Use the 23-pin cable a

2-10 | Chapter 2 Installation Note The wire color code may not match the Figure. Verify each wire is labeled with a function. DO NOT remove the labe

Detailed Installation | 2-11 a. Identify the cables required for attaching to the 23-pin connector. There should be a minimum of three (3), power (1

2-12 | Chapter 2 Installation l. Identify each wire on the site installed cables and label it (A, B, C, D, etc.) in accordance with the labels on t

FCC Notice Note: Complies with Federal Communications Commission Rules & Regulations Part 15, Subpart B for a Class A digital device. WARNING Th

Detailed Installation | 2-13 Housing Connections All the necessary connections are provided at the top of the housing, including the 23-pin connecto

2-14 | Chapter 2 Installation DIP Switch Location on CI Board Caution Changing the positions on the DIP switch on the Main board shoul

Detailed Installation | 2-15 Position 7 – Set password. OFF = Default Position (default password is password or 1234). ON = Set new password; must be

2-16 | Chapter 2 Installation holes. Install the eight (8) screws and tighten only with a torque wrench set for 15-in. lb (170-N cm) of force. Use a

Detailed Installation | 2-17 Warning Do not use any gas type other than dry Nitrogen. The use of Shop Air can introduce moisture into the housing ass

2-18 | Chapter 2 Installation Pipe Mount Method Use this method to install, wire and configure a pipe mounted unit. Refer to Figure below as require

Detailed Installation | 2-19 Installing the 23-Pin Connector Assembly (If the prefabricated 23-pin cable assembly is used.) 6. Use the 23-pin cable

2-20 | Chapter 2 Installation Note The wire color code may not match the Figure. Verify each wire is labeled with a function. DO NOT remove the labe

Detailed Installation | 2-21 a. Identify the cables required for attaching to the 23-pin connector. There should be a minimum of three (3), power (1

2-22 | Chapter 2 Installation l. Identify each wire on the site installed cables and label it (A, B, C, D, etc.) in accordance with the labels on t

Important Safeguards – Outdoor Use GRAPHIC SYMBOL EXPLANATION The lightening bolt symbol alerts the user to the presence of dangerous voltage that may

Detailed Installation | 2-23 Housing Connections All the necessary connections are provided at the top of the housing, including the 23-pin connecto

2-24 | Chapter 2 Installation DIP Switch Location on CI Board Caution Changing the positions on the DIP switch on the Main board shoul

Detailed Installation | 2-25 Position 7 – Set password. OFF = Default Position. ON = Reset to default password (password or 1234); must be reset to O

2-26 | Chapter 2 Installation Pressurizing the Housing Assembly Refer to Figure below as needed. 21. Reattach the previously removed service cover t

Detailed Installation | 2-27 Warning Do not use any gas type other than dry Nitrogen. The use of Shop Air can introduce moisture into the housing ass

2-28 | Chapter 2 Installation Uninstalling If it becomes necessary to uninstall to pressurized Surveyor HD, follow the steps below. Warning Before

Configuration and Operation | 3-1 Surveyor HD Pressurized Network Dome XX214-60 Chapter 3 Configuration and Operation 3 This chapter will descri

3-2 | Chapter 3 Configuration and Operation XX214-60

Configuration and Operation | 3-3 Surveyor HD Pressurized Network Dome XX214-60 The “active” state can be programmed through the Surveyor HD web br

3-4 | Chapter 3 Configuration and Operation XX214-60

General Information | 1-1 Chapter 1 Introduction 1 This chapter provides general information about the Surveyor® HD and Surveyor SD Pressurized Ne

Operation, Maintenance and Reference | 4-1 Surveyor HD Pressurized Network Dome XX214-60 Chapter 4 Operation, Maintenance and Reference 4 This c

4-2 Operation, Maintenance and Reference e XX214-60

Operation, Maintenance and Reference | 4-3 Surveyor HD Pressurized Network Dome XX214-60 Maintenance The Pressurized Surveyor HD requires no schedu

Shipping Instructions Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at

Operation, Maintenance and Reference | 4-5 Surveyor HD Pressurized Network Dome XX214-60 Network Cable Caution Careful selection of proper cable is

4-6 Operation, Maintenance and Reference e XX214-60

Operation, Maintenance and Reference | 4-7 Surveyor HD Pressurized Network Dome XX214-60 Backlight Compensation: On/Off, selectable. Iris Control

4-8 Operation, Maintenance and Reference e XX214-60

Vicon Standard Equipment Warranty Vicon Industries Inc. (the “Company”) warrants your equipment to be free from defects in material and workmanship u

Vicon Industries Inc. For office locations, visit the website: www.vicon-security.com

1-2 | Chapter 1 Introduction General Information The information in this manual covers the installation and operation of the Surveyor HD and Surveyo

General Information | 1-3 Table 1: Models and Descriptions Model Number Environment Resolution Mount Type Optical Zoom/ Digital Zoom Lower Dome Type

1-4 | Chapter 1 Introduction Organization of this Manual Chapter Description 1 Introduction: Provides general information about the Surveyor HD/SD P

Installation | 2-1 Chapter 2 Installation 2 This chapter provides installation information for the Surveyor HD/SD Pressurized Network Dome. The ch

2-2 | Chapter 2 Installation Installation Caution This unit should only be installed by a qualified technician using common hand tools and approved