Vicon IX 2000 L Technical Information Seite 133
- Seite / 256
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
MX Control Card Configuration
Vicon MX Hardware System Reference A-21
Device 1 and Device 2 Option Cards
This section describes how to use the connectors that are available
on the MX option cards that can be installed and accessed from the
Device 1 and Device 2 slots in the rear panel of the MX Control:
• Analog Option
• Audio Option on page A-24
Important
These option cards may be factory installed. If they were not originally
ordered, the slot is covered with a blank panel. You can install one or more
of these cards, as appropriate, later.
For details on the functionality that these options for the MX Control
supports for connecting to external analog and audio sources, see
Chapter 4 MX Control.
Analog Option
To connect an analog ADC card in the MX Control to third-party
devices for capturing analog data, you must plug one end of the
supplied 100-way cable into the
Analog socket on the rear of the
MX Control and the other end into the Vicon patch panel. You may
need to create your own plug to connect the Vicon patch panel to your
analog devices, such as force plates, electromyography (EMG)
equipment, and potentiometers.
Important
There can be two analog ADC cards installed in an MX Control. Depending
upon the options you ordered for your Vicon MX system, your MX Control may
not have an analog ADC card installed. For details of how to integrate one
later, see Installing an MX Option Card on page A-25.
The analog ADC card is a 64-channel device for generating 16-bit
offset binary conversions from analog sources. The input impedance
is 1 M
Ω. The data sampling frequency is common to all channels; it
is affected by the MX Camera frame rate specified in the Vicon
application software. The higher the sampling frequency, the fewer
analog channels there are available. Each channel has a
programmable gain, which can be set to +/- 10 volts, +/- 5 volts,
+/- 2.5 volts, or +/- 1.25 volts. For details on specifying these
settings, see your Vicon software documentation.
MXhardware_Reference.book Page 21 Monday, April 30, 2007 1:56 PM
- System Reference 1
- Vicon MX Hardware 1
- Contents 3
- Audience 9
- Structure 10
- Conventions 12
- Related documentation 13
- System Information 15
- MX Software 16
- MX Peripherals 16
- Third-Party Devices 16
- Environmental Regulations 17
- Safety Information 18
- Warranty 19
- CE Declaration of Conformity 20
- Introduction 23
- Vicon MX Architecture Models 25
- MX Bridge 29
- MX Bridge Rear Panel 31
- Supported Camera Modes 32
- MCam2 Cameras 33
- 14 for VCam/SVCam cameras 34
- Camera Select dial 35
- Camera Select 35
- MX Cameras 37
- Camera Lenses 39
- Field of View 40
- Figure 3-4: Image circle 42
- Aperture and Depth of Field 44
- Camera Lens Filters 44
- MX Camera Rear Panels 46
- Camera Lens Mount 49
- Tripod Mount 49
- Camera Strobe Units 50
- Strobe Unit Connections 51
- Strobe Unit Status Indicators 51
- Unassigned 53
- MX Control 55
- MX Control Rear Panel 58
- MX Host PC 67
- Ethernet Port on Host PC 68
- Vicon Software on Host PC 69
- Movie Capture Card on Host PC 70
- MX Link Front Panel 73
- MX Link Rear Panel 74
- MX Net Front Panel 77
- MX Net Rear Panel 79
- MX Sync Front Panel 81
- MX Sync Rear Panel 82
- MX Ultranet 85
- MX Ultranet Front Panel 86
- MX Ultranet Rear Panel 87
- MX Accessory Kit 93
- MX Cable Descriptions 97
- MX Cables 100
- Vicon Cameras 101
- MX Hardware Units 101
- MX Cable Order Information 102
- MX Calibration Kit 103
- Calibration Kit Contents 104
- MX Control Card Configuration 113
- Timecode and Genlock Option 114
- Ω (ohms) 114
- MX Control Standard Card 115
- Important 117
- Installing MX Option Cards 136
- Installing an MX Option Card 137
- Figure A-6: Vicon patch panel 139
- Figure A-7: 100-way cable 140
- Figure A-8: ADC edge socket 140
- GPIO and Remote Connections 141
- Electrical Specifications 142
- GPIO Functionality 144
- Custom GPO Programming 145
- GPO File Format 146
- GPO File Structure 146
- XML Header 149
- AllPrograms section 149
- GPO File Attribute Syntax 149
- Program Name Section 150
- Type Section 150
- Polarity Section 151
- StartEvent Section 151
- StopEvent Section 152
- StartOffset Section 152
- StopOffset Section 153
- PulseWidth Section 153
- Remote Functionality 154
- Remote Control Operation 155
- Remote Output Status Events 156
- MX Camera Lens Focusing 157
- Figure C-5: Camera focus ring 165
- Merged Markers 167
- Technical Specifications 169
- MX Camera Specifications 170
- MX40+, MX40 179
- MX Control Specifications 185
- MX Link Specifications 186
- MX Net Specifications 187
- MX Sync Specifications 188
- MX Ultranet Specifications 189
- Regulatory Notices 191
- 9) the appropriate boxes 193
- Medical Devices 194
- Female Male 197
- lb kg 197
- Section C. Device Information 199
- Product Configurations and 203
- Software Options 203
- Troubleshooting 205
- Support Resources 209
- Useful References 210
- Vicon Online Support (VOS) 210
- Documentation Feedback 213
- Customer Satisfaction Survey 215
- Glossary 217
- Aspect ratio 218
- Calibration wand 220
- Capture space 221
- .csm file 223
- Ghost marker 228
- Kinematics 230
- Motorcycle pose 232
- MX F-series Camera 233
- .obj file 235
- RealTime subject 238
- Rotation 239
- Secondary selection 240
- Subject calibration 242
- Trajectory 244
- Virtual point 246
- Walking speed 247
- .xml file 248
- Numerics 249
Verwandte Produkte und Handbücher für Sicherheitskameras Vicon IX 2000 L
Sicherheitskameras Vicon SVR-PC Bedienungsanleitung
(122 Seiten)
(122 Seiten)
(67 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern