Vicon IX 2000 L Technical Information Seite 32
- Seite / 256
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
MX Bridge
2-4 Vicon MX Hardware System Reference
•Analog Camera
Three pairs of connectors for camera channels 1, 2, and 3:
• 12-pin Lemo socket for connecting to an MCam2, VCam,
SVCam, MCam(PAL), or MCam(NTSC) camera.
• BNC socket located to the right of the 12-pin Lemo connector
for connecting to an MCam camera.
Warning
Do not use this socket to connect an MX Bridge unit to either an MX Net
unit or an MX Link unit. Plugging the 12-pin Lemo plug on one end of an
MX cable into this Analog Camera socket and the other end of the plug
into either the Link Connect socket on the rear panel of an MX Link or
the Link socket on the rear panel of an MX Net will result in damage to
the units. For details on these other MX units, see Chapter 6 MX Link and
Chapter 7 MX Net. For details on the cables to connect these MX units,
see Chapter 11 MX Cables.
•Net Connect
10-Pin Lemo socket located to the right of each set of Analog
Camera connectors. This connects the MX Bridge to an
MX Ultranet or an MX Net, which supplies power and
synchronization to each connected camera and carries the signal
to and from it. For details on these other MX units, see
Chapter 7 MX Net and Chapter 9 MX Ultranet. For details on the
cables to connect these MX units, see Chapter 11 MX Cables.
• External Interface
9-pin D-type RS-232 serial socket. This provides an interface to
the cameras connected to the MX Bridge and is typically used only
for factory test purposes.
Supported Camera Modes
Camera-specific cabling connects the supported Vicon cameras to the
MX Bridge camera channel inputs (for details, see Chapter 11 MX
Cables). The MX Bridge unit is configured to identify the connected
camera type and pass this information to the Vicon application
software on the host PC.
The following sections give the performance details for the V-series
cameras that can be connected to Vicon MX through an MX Bridge:
•MCam2
•VCam
• SVCam
MXhardware_Reference.book Page 4 Monday, April 30, 2007 1:56 PM
- System Reference 1
- Vicon MX Hardware 1
- Contents 3
- Audience 9
- Structure 10
- Conventions 12
- Related documentation 13
- System Information 15
- MX Software 16
- MX Peripherals 16
- Third-Party Devices 16
- Environmental Regulations 17
- Safety Information 18
- Warranty 19
- CE Declaration of Conformity 20
- Introduction 23
- Vicon MX Architecture Models 25
- MX Bridge 29
- MX Bridge Rear Panel 31
- Supported Camera Modes 32
- MCam2 Cameras 33
- 14 for VCam/SVCam cameras 34
- Camera Select dial 35
- Camera Select 35
- MX Cameras 37
- Camera Lenses 39
- Field of View 40
- Figure 3-4: Image circle 42
- Aperture and Depth of Field 44
- Camera Lens Filters 44
- MX Camera Rear Panels 46
- Camera Lens Mount 49
- Tripod Mount 49
- Camera Strobe Units 50
- Strobe Unit Connections 51
- Strobe Unit Status Indicators 51
- Unassigned 53
- MX Control 55
- MX Control Rear Panel 58
- MX Host PC 67
- Ethernet Port on Host PC 68
- Vicon Software on Host PC 69
- Movie Capture Card on Host PC 70
- MX Link Front Panel 73
- MX Link Rear Panel 74
- MX Net Front Panel 77
- MX Net Rear Panel 79
- MX Sync Front Panel 81
- MX Sync Rear Panel 82
- MX Ultranet 85
- MX Ultranet Front Panel 86
- MX Ultranet Rear Panel 87
- MX Accessory Kit 93
- MX Cable Descriptions 97
- MX Cables 100
- Vicon Cameras 101
- MX Hardware Units 101
- MX Cable Order Information 102
- MX Calibration Kit 103
- Calibration Kit Contents 104
- MX Control Card Configuration 113
- Timecode and Genlock Option 114
- Ω (ohms) 114
- MX Control Standard Card 115
- Important 117
- Installing MX Option Cards 136
- Installing an MX Option Card 137
- Figure A-6: Vicon patch panel 139
- Figure A-7: 100-way cable 140
- Figure A-8: ADC edge socket 140
- GPIO and Remote Connections 141
- Electrical Specifications 142
- GPIO Functionality 144
- Custom GPO Programming 145
- GPO File Format 146
- GPO File Structure 146
- XML Header 149
- AllPrograms section 149
- GPO File Attribute Syntax 149
- Program Name Section 150
- Type Section 150
- Polarity Section 151
- StartEvent Section 151
- StopEvent Section 152
- StartOffset Section 152
- StopOffset Section 153
- PulseWidth Section 153
- Remote Functionality 154
- Remote Control Operation 155
- Remote Output Status Events 156
- MX Camera Lens Focusing 157
- Figure C-5: Camera focus ring 165
- Merged Markers 167
- Technical Specifications 169
- MX Camera Specifications 170
- MX40+, MX40 179
- MX Control Specifications 185
- MX Link Specifications 186
- MX Net Specifications 187
- MX Sync Specifications 188
- MX Ultranet Specifications 189
- Regulatory Notices 191
- 9) the appropriate boxes 193
- Medical Devices 194
- Female Male 197
- lb kg 197
- Section C. Device Information 199
- Product Configurations and 203
- Software Options 203
- Troubleshooting 205
- Support Resources 209
- Useful References 210
- Vicon Online Support (VOS) 210
- Documentation Feedback 213
- Customer Satisfaction Survey 215
- Glossary 217
- Aspect ratio 218
- Calibration wand 220
- Capture space 221
- .csm file 223
- Ghost marker 228
- Kinematics 230
- Motorcycle pose 232
- MX F-series Camera 233
- .obj file 235
- RealTime subject 238
- Rotation 239
- Secondary selection 240
- Subject calibration 242
- Trajectory 244
- Virtual point 246
- Walking speed 247
- .xml file 248
- Numerics 249
Verwandte Produkte und Handbücher für Sicherheitskameras Vicon IX 2000 L
Sicherheitskameras Vicon SVR-PC Bedienungsanleitung
(122 Seiten)
(122 Seiten)
(67 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.184 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern